How to Replace a Saab 9-3 Key The Saab 9-3 has an impressive attraction for drivers. It has excellent visibility and a strong performance engine. It has a very high safety rating. However, it's important to make sure that you have at minimum two keys working for your car. If you lose the only key, it can be very costly to buy an additional one. How to Replace the Ignition Key in a Saab9-3 If your car's keys won't turn on you must replace it. This guide will walk you through how to do it on a Saab 9-3. You will need a replacement key as well as a reprogrammable battery as well as a new key-fob case. As opposed to earlier models, modern Saab vehicles use a transponder on the key-fob rather than a physical metal key to unlock and start the car. The issue with this is that the reprogrammable batteries in the key-fob will wear out and lose charge any longer. This is especially when you use the same key for the lock you have. A professional locksmith can change the battery with ease. You can also do it yourself if have the proper tools and a bit of patience. The first step is to take the key-fob off. This is accomplished by inserting a flathead screwdriver into the slot that is located in the middle of the case. The plastic is brittle, and it is susceptible to being damaged. Once the case has been opened, you can create the new key by combining the lower part of the key from earlier with banana and transponder. This will ensure the new key is properly mated to your CIM and can make a huge difference when replacing the sole key of your Saab 9-3. How do I replace the ignition Key in a Saab 900 If you don't have two keys, you will need remove the dashboard and steering wheel in order to access the ignition. Begin by disconnecting the negative battery cable. After the battery has been disconnected, you can take off all trim pieces and dashboard pieces that surround the steering wheel. Once the dashboard is removed, insert an screwdriver into the opening behind the ignition switch. The ignition cylinder houses the key lock, which can prevent the car from starting if a key isn't in it. If the ignition switch on your 900 isn't functioning, check the key to determine if it's in the lock or is stuck in the barrel of the ignition. It is also important to rotate your keys and keep them clean to avoid bent. Saab cars differ from other vehicles because they don't have traditional keys made of metal. Instead, the car recognizes the electronic signals from the key fob by a specific chip inside it. If you lose only one working key fob the dealer will charge you top dollar for the replacement of the computer module (known as the CIM). We can reprogram the EEPROM on your current computer to enable it to accept new keys without the need to replace it. You will save over 50% off the dealer's cost! We call it the SAAB KEY PROGRAM. Find out more information about it here! How to replace the ignition Key on a Saab 9-5 The metal component of classic Saab keys is easy to copy and does not represent a significant risk to theft of vehicles. The electronic component of the key-fob comes with an embedded chip that can identify the car when the key is placed in the ignition switch. Saab's anti-theft system has relied upon this technology for over 10 years. It's not as effective as a door lock however it makes stealing your car a lot more difficult. This is the reason why every Saab owner should always keep an extra key on hand. The majority of new Saabs are delivered with two keys, but they can be purchased from an dealer by using a handheld device known as a Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this rule is the NG 9-3 models, which are more modern and newer features that require the use of a key-fob. If you lose all keys in the event of a loss, the dealer will replace your CIM or TWICE modules and charge an extra fee. We can reprogram your computer's EEPROM to accept new keys without having to replace expensive modules. How do I replace the ignition Key on a Saab XC90 It may be time to replace your SAAB key fob if it is having trouble turning the lock barrel. The process is simple and you don't have to visit a dealership. You can do it at home with just a few simple tools. First, you'll need prepare the new key. Before you begin, disable the anti-theft by placing blocks under your rear wheels and releasing your handbrake. Then, you can put the key in the ignition and turn it to the on position that activates the accessories but does not start the engine. Repeat saab key fob replacement , and then put the key on the on position. Then you'll need to buy an additional case for your key fob. They are readily available at many auto parts stores and are typically quite affordable. You can get them with or without electronics, depending on the model. To open the case to open the case, gently push the screwdriver with a flathead into the slot in the middle. When you've split the case, you will be able to access all the internal electronics. Use a flathead screwdriver to gently pull out the electronic components.
saab key fob replacement
